Hi, I looked for all the CANbus parameters in my new Dudu7 and I can only find a recent Suzuki Swift option in OD under OD-Suzuki-All. And it doesn’t work. Do you have a recommendation?
CANbus setup for Swift 2020
Raise/vw/pq/low
Thanks unfortunately it is not working. I’ll try other Suzuki cars
- Edited
I came accros a setup guide for all makes on teyes website, the only option for Suzuki given was ignis 2016-2020 which was Raise(RZC)>SUZUKI>IGNIS>2016
Its worth a try as I can't get an exact match for my mercedes c180 2006, nearest is b200/viano but it works
It does not work when you set it to Suzuki/model
If you have a OD-LM-01 adapter you have to set it to raise/vw/pq/low
This was told by the DUDU devs.
But there seems to be hiword adapters for Suzuki, but i don't know what you have to set in DUDU
Thanks for the suggestions. I tried the following ones without success:
- RZC/Suzuki//Ignis/2016
- Hiworld/Suzuki/Scross/2022 (hi/med/low) all three variants
- Hiworld/Suzuki/Baleno/2023
- Hiworld/Suzuki/Fronx/2023
- OD/Suzuki/All/OD
JhonnyD, appreciate the external CANbus decoder suggestion. "OD-LM-01" seems easily available. How do you connect it to the head unit? Do you need a Y type harness to connect both to Dudu7 and to the OD-LM-01 decoder?
I just saw that the first input in Dudu7 ("C" above the fan) says "Audio and CAN", I guess this where you connect the OD-LM-01?
Or maybe it comes with its own harness, in which you need to make sure it is Dudu7 compatible
9 days later
Hi, I bought the special harness with the OD-LM-01 box. Plugged the wired OBD2 and the CANbox connector on the head unit side… and nothing happens (I tried both Raise/vw/pq/low and Hi). I reset the unit a few times. Nothing is detected. Not the opening door, Not the AC on/off or temperature, Not the reverse gear. Is there something else to do?
It did say Swift 2020 compatible
- Edited
Since the other features of the head unit work ok (except all the USB-A and C plugs, see other post), I asked the harness manufacturer to confirm the compatibility with my vehicle. In terms of connectivity you can’t be wrong (main connector and CANbus decoder out towards the head unit ; wired OBD2, connector towards the OD-LM-01 decoder, FM antenna) don’t need the green OEM cam connector because I have the 360 cams.
- Edited
Hi is there a way to check that the CANbus decoder is working properly? Because I didn’t witness any change when I plugged it in the head unit (door opening, AC on/off, proximity radar, etc. Nothing is detected) so either the harness is not wired properly or the decoder is not functional
- Edited
I contacted the CANBus harness manufacturer and they recommended RZC-VW-MQB All-XX settings. There is an improvement, the car OEM categories are recognized (displayed with specific icons) but as soon as I tried to change any of them, the change is rejected. And of course the "events" (opening the door, open the AC, etc.) are not recognized or displayed.
I tried with all sub categories Low / High AMP / Mixed / 360 Retrofit / Mixed same symptoms all around
I ordered another "OD-LM-01" harness from another manufacturer (after asking for their recommendation of the specific model). But this "trial and error" situation is a little bit annoying. I am ok with "not everything OK out of the box", but just getting actionable information is difficult and the cost just keeps going up...
Is there a possible setting in the "Factory setting" sub menu?